A broad overview of how modern Linux systems boot
For reasons beyond the scope of this entry, today I feel like writing down a broad and simplified overview of how modern Linux systems boot. Due to being a sysadmin who has stubbed his toe here repeatedly, I'm going to especially focus on points of failure.
- The system loads and starts the basic bootloader somehow, through either
BIOS MBR booting or UEFI. This can involve many steps on its own
and any number of things can go wrong, such as unsigned UEFI
bootloaders on a Secure Boot system.
Generally these failures are the most total; the system reports there's
nothing to boot, or it repeatedly reboots, or the bootloader aborts
with what is generally a cryptic error message.
On a UEFI system, the bootloader needs to live in the EFI system partition, which is always a FAT32 filesystem. Some people have had luck making this a software RAID mirror with the right superblock format; see the comments on this entry.
- The bootloader loads its configuration file and perhaps additional
modules from somewhere, usually your
/bootbut also perhaps your UEFI system partition. Failures here can result in extremely cryptic errors, dropping you into a GRUB shell, or ideally a message saying 'can't find your menu file'. The configuration file location is usually hardcoded, which is sometimes unfortunate if your distribution has picked a bad spot.
For GRUB, this spot has to be on a filesystem and storage stack that GRUB understands, which is not necessarily the same as what your Linux kernel understands. Fortunately GRUB understands a lot these days, so under normal circumstances you're unlikely to run into this.
(Some GRUB setups have a two stage configuration file, where the first stage just finds and loads the second one. This allows you more flexibility in where the second stage lives, which can be important on UEFI systems.)
- Using your configuration file, the bootloader loads your
chosen Linux kernel and an initial ramdisk into memory and
transfers control to the kernel. The kernel and initramfs image
also need to come from a filesystem that your bootloader understands,
but with GRUB the configuration file allows you to be very flexible
about how they're found and where they come from (and it doesn't have to be the same
grub.cfgis, although on a non-UEFI system both are usually in
There are two things that can go wrong here; your
grub.cfgcan have entries for kernels that don't exist any more, or GRUB can fail to locate and bring up the filesystem where the kernel(s) are stored. The latter can happen if, for example, your
grub.cfghas the wrong UUIDs for your filesystems. It's possible to patch this up on the fly so you can boot your system.
- The kernel starts up, creates PID 1, and runs
/initfrom the initramfs as PID 1. This process and things that it run then flail around doing various things, with the fundamental goal of finding and mounting your real root filesystem and transferring control to it. In the process of doing this it will try to assemble software RAID devices and other storage stuff like LVM, perhaps set sysctls, and so on. The obvious and traditional failure mode here is that the initramfs can't find or mount your root filesystem for some reason; this usually winds up dropping you into some sort of very minimal rescue shell. If this happens to you, you may want to boot from a USB live image instead; they tend to have more tools and a better environment.
(Sometimes the reasons for failure are obscure and annoying.)
On many traditional systems, the initramfs
/initwas its own separate thing, often a shell script, and was thus independent from and different from your system's real init. On systemd based systems, the initramfs
/initis actually systemd itself and so even very early initramfs boot is under systemd's control. In general, a modern initramfs is a real (root) filesystem that processes in the initramfs will see as
/, and its contents (both configuration files and programs) are usually copied from the versions in your root filesystem. You can inspect the whole thing with
Update: It turns out that the initramfs init is still a shell script in some Linux distributions, prominently Debian and Ubuntu. The initramfs init being systemd may be a Red Hat-ism (Fedora and RHEL). Thanks to Ben Hutchings in the comments for the correction.
How the initramfs
/initpivots into running your real system's init daemon on your real system's root filesystem is beyond the scope of this entry. The commands may be simple (systemd just runs '
systemctl switch-root'), but how they work is complicated.
(That systemd is the initramfs
/initis convenient in a way, because it means that you don't need to learn an additional system to inspect how your initramfs works; instead you can just look at the systemd units included in the initramfs and follow along in the systemd log.)
- Your real init system starts up to perform basic system setup to
bring the system to a state that we think of as the normal basic
way it is; basically, this is everything you usually get if you
boot into a modern single user mode. This does things like set
the hostname, mount the root filesystem so it can be written to,
apply your sysctl settings (from the real root filesystem this
time), configure enough networking so that you have a loopback
device and the IPv4 and IPv6 localhost addresses, have udev fiddle
around with hardware, and especially mount all of your local
filesystems (which includes activating underlying storage systems
like software RAID and LVM, if they haven't been activated already
in the initramfs).
The traditional thing that fails here is that one or more of your local filesystems can't be mounted. This often causes this process to abort and drop you into a single user rescue shell environment.
(On a systemd system the hostname is actually set twice, once in the initramfs and then again in this stage.)
- With your local filesystems mounted and other core configuration
in place, your init system continues on to boot your system the
rest of the way. This does things like configure your network
(well, perhaps; these days some systems may defer it until you
log in), start all of the system's daemons, and eventually enable
logins on text consoles and perhaps start a graphical login
environment like GDM or LightDM. At the end of this process, your
system is fully booted.
Things that fail here are problems like a daemon not starting or, more seriously, the system not finding the network devices it expects and so not getting itself on the network at all. Usually the end result is that you still wind up with a login prompt (either a text console or graphics), it's just that there were error messages (which you may not have seen) or some things aren't working. Very few modern systems abort the boot and drop into a rescue environment for failures during this stage.
On a systemd system, this transfers control from the initramfs systemd to the systemd binary on your root filesystem (which takes over as PID 1), but systemd maintains continuity of its state and boot process and you can see the whole thing in
journalctl. The point where the switch happens is reported as 'Starting Switch Root...' and then 'Switching root.'
All of System V init, Upstart, and systemd have this distinction
between the basic system setup steps and the later 'full booting'
steps, but they implement it in different ways. Systemd doesn't
draw a hard distinction between the two phases and you can shim
your own steps into either portion in basically the same way. System
V init tended to implement the early 'single user' stage as a
separate nominal runlevel, runlevel 'S', that the system transitioned
through on the way to its real target runlevel. Upstart is sort of
a hybrid; it has a
startup event that's
emitted to trigger a number of things before things start fully
(This really is an overview. Booting Linux on PC hardware has become a complicated process at the best of times, with a lot of things to set up and fiddle around with.)
Comments on this page:Written on 17 June 2018.